|
|
Post by KRAZY RICK on Jan 10, 2013 7:35:02 GMT -4
That should fly for sure, with those engines !!!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 10, 2013 12:06:18 GMT -4
[glow=red,2,300]NEED MORE INTAKE!!![/glow] I decided to extend the Intakes so that the front 1/2 inch of the Engines fits inside the Intakes. So I cut some more of the Intakes off the old Jet Model.  Next I cut the New Intakes down to fit the Pegasus.  Here it is glued in place.  I glued a piece of sheet plastic to the underside of the Intake to finish it off!   |
|
|
|
Post by KRAZY RICK on Jan 10, 2013 13:11:14 GMT -4
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 10, 2013 18:13:24 GMT -4
[glow=red,2,300]SHAPING THE INTAKES!!![/glow] I have marked the bottoms of the Intakes for Cutting. I will cut along these lines with a razor saw.  After cutting I glued these two pieces of plastic over the cut areas.  Then I carved the plastic down to the shape of the Intake using a Dremel Tool and sanded it smooth & even with a Fileboard.  Next I cut the bottom of the Intakes and did the same thing to the bottoms. Then I did the same thing again to the sides...  Here are the Intakes with all four sides done!  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 10, 2013 18:24:55 GMT -4
[glow=red,2,300]BARS UP FRONT!!![/glow] I found this part in the parts box. I think it is part of a tail light assembly...  I cut the two ends off and glued them in place as shown!  Here are the Intakes after a little sanding...  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 13, 2013 11:50:17 GMT -4
That should fly for sure, with those engines !!! Oh Yeah, it should be pretty fast...  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 17, 2013 16:47:16 GMT -4
[glow=red,2,300]PRIMER TIME!!![/glow] I added the GTP Wing and got a couple coats of Filler/Primer on the Pegasus!  Front...  Any Color or Race Sponser Suggestions???  |
|
|
|
Post by KRAZY RICK on Jan 17, 2013 22:05:29 GMT -4
I don't know why .... but I keep thinking it would be neat as one of Batman's vehicles....Painted Black; with some red stripes, or highlights maybe
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 19, 2013 11:21:19 GMT -4
I don't know why .... but I keep thinking it would be neat as one of Batman's vehicles....Painted Black; with some red stripes, or highlights maybe Thanks for the suggestion Rick! |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 5, 2013 12:08:18 GMT -4
[glow=red,2,300]PEGASUS GETS IT'S WINGS!!![/glow] Well maybe not Wings...More like Four New Fins!  I cut these from sheet plastic and glued them in place with Zap-A-Gap/Green Label...  More Coming... |
|
|
|
Post by KRAZY RICK on Feb 5, 2013 15:50:30 GMT -4
It looks like a APV now too  ... ( All purpose Vehicle: Land, Air, Sea )  !!!!! |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 7, 2013 19:06:27 GMT -4
[glow=red,2,300]SPOILERS!!![/glow] I cut 2 lengths of 5/16th inch wide Plastic Strip and glued them in place to extend the Spoilers...  I made 2 Jet Engine Mounts from Sheet Plastic and attached them as shown.  This View shows the Engine Mounts and all 6 of the Pegasus Fins!  Side View!  Hope you like it so far... |
|
|
|
Post by KRAZY RICK on Feb 7, 2013 19:12:14 GMT -4
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 7, 2013 23:34:56 GMT -4
[glow=red,2,300]ME EITHER!!![/glow] ;D |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 13, 2013 13:08:09 GMT -4
[glow=red,2,300]ROUNDING THE INTAKES!!![/glow] I rounded out the inside of the Intakes with "Half-Round" Plastic Strip and Putty...  Got the Fins and Spoilers molded in, nice & smooth. Most of the Body & Underbody work is done now, so I applied some more primer.  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 25, 2013 4:57:36 GMT -4
[glow=red,2,300]INTERIOR STRIPS!!![/glow] First I made the rear of the Interior with two 5/16" Plastic Strips on each side. This was easier than trying to cut a template add fit one piece of plastic on each side.  Then I glued a 5/16" Strip on each side of the Cockpit...  The strips were positioned to add a little more room for the Engines!  More Coming... |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 25, 2013 11:50:02 GMT -4
[glow=red,2,300]INTERIOR SIDES...[/glow] I cut 2 side walls from sheet plastic and glued them in place. This will leave just enough room for the BiG Engines!  The fronts of the Interior Sides were attached to the Intake Shafts to complete them.  The Sides were cut so that they fit up against the Underbody tightly.  More Coming... |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Feb 27, 2013 16:07:04 GMT -4
[glow=red,2,300]SIDEWINDER DASH!!![/glow] The dashboard from Revells Dodge Sidewinder will be perfect for Pegasus! Just have to cut a little here...  Then I turned it up side down and carved away a little more, to add some legroom...  Here it is up-side down and carved to fit, perfect for Pegasus!  More Coming... |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 1, 2013 5:02:20 GMT -4
[glow=red,2,300]MOUNTING THE DASH...[/glow] I traced the edge of the dashboard on to the body. By cutting this area out, I will be able to mount the dash about 1/4" forward.  Here it is in place!  |
|
|
|
Post by KRAZY RICK on Mar 1, 2013 8:33:21 GMT -4
That dash looks perfect now !!
|
|
... ( All purpose Vehicle: Land, Air, Sea ) 