Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 30, 2012 22:06:39 GMT -4
[glow=red,2,300]PEGASUS!!![/glow] Pegasus is a Anti-Gravity Racer with Pod Racer Engines. The Most of the parts are from the Monogram Mustang GTP Kit. The Engines are from the AMT Star Wars Pod Racer Kit.  I am going to take the Intakes from the Jet and modify them to fit the Mustang...  I cut the front of the Mustang off with a razor saw and got the Intakes off of the old plane without breaking them!  With a little trimming I got the Intakes to fit!  More Coming...  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 30, 2012 23:40:06 GMT -4
[glow=red,2,300]TWO BIG INTAKES!!![/glow] I cut 2 pieces of sheet plastic to fit along the hood lines. These will be the inside walls of the Intakes...  Next I cut 2 pieces of plastic to fill in the areas on the tops of the Intakes...  Then I cut 2 more pieces of plastic, to fill in the bottoms on the Intakes...  More Coming... |
|
|
|
Post by KRAZY RICK on Dec 31, 2012 8:39:02 GMT -4
This should be interesting Ira !!!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 31, 2012 11:12:38 GMT -4
[glow=red,2,300]THE UNDERSIDE!!![/glow] I cut the front off of the Underbody...  Here it is in place!  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 31, 2012 14:59:17 GMT -4
[glow=red,2,300]PEGASUS PROGRESS!!![/glow] Here are a few photos showing the Pegasus as it is now...  Side...  I mounted the Jet Intakes Out about an 1/8 inch so that they would form these Vents!  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Dec 31, 2012 15:40:48 GMT -4
This should be interesting Ira !!! [glow=red,2,300]THAT'S FOR SURE!!![/glow] |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 1, 2013 3:47:14 GMT -4
Hey Ira Have you made any more progress on this ?
I'm amazed at how you could imagine the Intakes from a Phantom fitting so well
onto the fronts of that Mustang !! Great Project.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 1, 2013 14:20:32 GMT -4
[glow=red,2,300]ROUNDIN' OFF...[/glow] I cut 4 pieces of Half-Round Plastic Strip and glued them in the 4 inside joints of the Intake...  Then I Filed and Sanded the outside corners Nice & Curved Around...  Progress Shot!  More Coming... |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 1, 2013 16:20:10 GMT -4
I can just see where that's going. COOL idea.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 2, 2013 10:57:08 GMT -4
I can just see where that's going. COOL idea. Thanks! |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 2, 2013 18:34:51 GMT -4
[glow=red,2,300]BiG MUSTANG GRILL!!![/glow] I am using an 1/16th scale 1964 Mustang Grill, with "Floating" Horse Emblem for the Pegasus!  I had to reduce it's width a little bit.  I cut a piece of plastic to mount the New Hood to and glued it in place...  After a lot of planning & figuring I found the best position for the Grill and glued it in place!  More Coming... |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 2, 2013 18:59:40 GMT -4
[glow=red,2,300]BiG MUSTANG HOOD!!![/glow] I'm using the hood from an AMT 1/16th scale 1964 Mustang for the Pegasus...  I measured the size I need and cut it out of the BiG Hood.  Here is the New Hood glued in place!  I cut a piece of sheet plastic for a Front Pan for the Pegasus and glued it in place...  I cut 2 small strips of plastic and glued them at both ends of the Grill to finish it off!  More Coming... |
|
|
|
Post by KRAZY RICK on Jan 3, 2013 9:34:27 GMT -4
Wow Ira, Your Really rolling along with all these builds !!!!
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 3, 2013 15:48:35 GMT -4
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 3, 2013 21:56:00 GMT -4
[glow=red,2,300]BACK DOOR MUSTANG!!![/glow] The Pegasus will have a BiG Jet Engine on each side of the body, blocking the doors, so I'm going to put in a Rear Door in for Driver Access! I drew 2 lines from the rear window back. Then I drew 2 more lines about 1/8th inch wider at the rear. I will cut on the outside lines...  I marked the underbody with the same shape as above except, its about 3/8th inches shorter...  I used a Zona Saw and cut out the rear deck.  Then I cut out the underbody section with a Zona Saw and X-Acto Knife.  Here is the Body/Underbody Test Fit...  It Fits! |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 4, 2013 11:52:22 GMT -4
[glow=red,2,300]FABRICATION...[/glow] I cut ot 2 pieces of sheet plastic to fill in the Cut-Out Area. I glued them to the Body, but not the Underbody...yet. I cut out a Door Frame and fit it in place, no glue on this piece yet.  Side View...  Top...  [glow=red,2,300]What Next???[/glow] |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 7, 2013 12:06:23 GMT -4
[glow=red,2,300]MAKIN' ROOM FOR THE BiG ONES!!![/glow] I'm cutting away more body and undrbody to make room foor the Engines. I cut about 3/16th of an inch off the both edges of the Underbody including the 2 Fins...  I cut out 2 New Larger Under Fins from sheet plastic...  Here are the New Under Fins glued in place!  Next I cut out more of the underbody to make room for the Engines.  I cut a little too much from the body so I put in a 1/4 inch patch.  That should be enough room... |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 7, 2013 12:48:43 GMT -4
[glow=red,2,300]THIS IS JUST A TEST!!![/glow] Here are a few photos of Engines in position, no glue yet...  Top View!  Wanna' Race???  Last one...  |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 8, 2013 2:57:57 GMT -4
LOOKN COOL.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Jan 9, 2013 20:18:04 GMT -4
Thanks! |
|
